Vaporesso Pod Not Detected, Burnt Taste or Leaking: XROS Fixes That Work

A Vaporesso pod that is not detected is nearly always a contact problem, so take the pod out, wipe the metal contacts on the pod base and inside the device with a dry cotton bud, refit it firmly, then try a different pod.
A burnt taste means the wick inside the pod has already scorched, and a scorched pod has to be replaced rather than rinsed or rested.
Most XROS leaks trace back to a mouthpiece that was not pushed fully home after filling, or a pod filled past the top of the window.
The same contact-first fix works on the Luxe XR Max, Dojo Blast 10K and SWAG PX80, but each one fails in its own way after that.
Pods from 0.6 ohm to 1.2 ohm fit every XROS device, while the Luxe XR Max and SWAG PX80 both run GTX coils instead.

Three faults account for most Vaporesso complaints, and all three have fixes you can do at the kitchen table in under five minutes. This guide covers the Vaporesso kits we stock, from the refillable XROS Mini to the prefilled Dojo Blast 10K, so you can find your own device rather than guess. We are an Online Vape Store UK and these are the questions we get asked most about Vaporesso pod kits.

Why Your Vaporesso Pod Is Not Detected

A "pod not detected" fault means the device cannot read the coil through the metal contacts at the base of the pod. It is a connection problem, not usually a dead device, and it works the same way on every Vaporesso pod kit.

Vaporesso's own XROS 4 Nano manual says the CHECK ATOMIZER error means the device cannot detect the pod or there is a connection issue, and it lists four fixes in order:

Clean the connection with a dry cloth or cotton bud, covering both the metal pins inside the battery and the contact points on the bottom of the pod.
Check the pod is fully inserted into the battery.
Remove the protective sticker from the base of the pre-installed pod if the kit is brand new.
Fit a new pod, because the coil inside may be damaged or reading too high a resistance.

Work through those in that order. The sticker catches out more new buyers than anything else on the list.

What to Check if the Error Keeps Coming Back

If the fault clears and then returns, the pattern tells you where the problem sits.

Returns only after filling: liquid is reaching the contacts, so wipe the pod base dry before you push it in.
Returns when you nudge the pod: the pod base, pin or magnet is worn, so fit a fresh pod.
Happens with every pod you own: the device is the issue, and Vaporesso's manual says do not attempt a repair yourself.
Still unclear: put a working pod in the failing device and the failing pod in a different device, because whichever part carries the fault is the one to replace.

What Vaporesso XROS Flashing Lights Mean

Flash codes differ between XROS models, so counting flashes only helps if you count them against the right manual.

The patterns that are consistent across published UK guidance:

XROS 3 and XROS 4: five flashes in the battery colour means the pod is not being read.
XROS 4 Mini: four flashes in the battery colour means no pod detected.
XROS 5 Mini and XROS 6 Mini: the manuals do not use colour for faults, and all lights flashing four times means no pod detected.
Any model, straight after a long draw: that is the eight-second cut-off, not a fault. Take a shorter puff.

Published sources disagree on what three flashes means on the XROS 4, some calling it a flat battery and others a short circuit, so check your own manual and charge the device fully first. The same contact-first logic applies to other brands, and our guide to fixing Hayati Pro Ultra Plus errors and blinking lights walks through the equivalent blink patterns on that kit.

Vaporesso XROS Burnt Taste Fix: What Actually Works

A burnt taste happens when the coil heats faster than the wick can resupply e-liquid. Once the cotton scorches, the taste is permanent and the pod or coil needs replacing, so everything below is about preventing the next one.

Symptom	Likely cause	What to do
Burnt on the first puff of a fresh pod	Wick was still dry when you fired it	Fill, wait, then take two gentle primer puffs
Burnt after a run of quick puffs	Chain vaping outpaced the wicking	Leave 15 to 30 seconds between draws
Burnt when the pod looks low	Wicking ports are uncovered	Refill before the pod drops below a third
Burnt with a thick, sweet liquid	VG too high, or sweetener residue on the coil	Switch to a 50/50 blend or a nic salt
Flavour fades, then turns sharp	Coil is at the end of its life	Replace the pod or coil

Two notes that matter on an XROS specifically.

Priming takes longer than you think. A review of the XROS Mini recommends leaving a filled pod to saturate for around ten minutes before the first draw, and five minutes is the usual minimum across the range.

On an XROS Mini you cannot turn the power down. The Mini runs at 11W to 16W and sets output from the pod it reads, so "lower your wattage" is advice for a different device. Your levers are pod resistance, liquid choice and puff spacing. Vaporesso's published best wattages run roughly 10W for the 1.2 ohm pod, 12W for the 1.0 ohm, 16W for the 0.8 ohm and 21W for the 0.6 ohm, and pods above 1.0 ohm want thinner liquid, so pair them with nicotine salts or a 50/50 blend rather than a high-VG shortfill.

Vaporesso XROS Leaking: Find Where It Is Coming From

XROS pods fill through a snap-off mouthpiece and have no separate fill plug, so there are only two leak paths. Fix the right one and it stops.

Weeping from the top or around the mouthpiece:

Push the mouthpiece fully home until it seats, because a partly closed mouthpiece is the most common cause.
Fill below the top of the window rather than to the brim, so air can still move.
Replace a pod that keeps weeping after you have dried it, refilled it and shut it firmly.

Liquid pooling in the device well or under the pod:

Pull the pod out and dry the well and the contact pins, getting into the recess where liquid collects.
Hold the pod up to the light and look for hairline cracks around the base.
Push the pod back in straight and firmly, with no wobble.

A little condensation in the airway is normal on any MTL pod kit. Liquid on your fingers or in your pocket is not.

Vaporesso Luxe XR Max Problems: GTX Coils and Wattage

The Vaporesso Luxe XR Max is a different animal to an XROS, so the fixes change. It runs a 2800mAh battery at 5W to 80W through a 2ml TPD pod, and the coil is a separate GTX coil you push into the pod rather than a sealed pod coil.

That means two extra things can go wrong, and one extra thing you can fix.

A GTX coil not seated properly reads as no coil detected or a burnt taste on the first puff. Push the coil fully into the pod base until it stops, then refit the pod.
The silicone plug on the pod base is the leak point. After filling, press it fully flat and flush, not at an angle.
Wattage is adjustable here, unlike the XROS Mini, so overpowering a coil is a real cause of burnt hits. Vaporesso's rough best wattages are 30W for the 0.4 ohm GTX, 28W for the 0.6 ohm, 12W to 16W for the 0.8 ohm and 8W to 12W for the 1.2 ohm.

If you are getting burnt hits on a Luxe XR Max, drop the wattage into the coil's printed range before you blame the coil. We stock the Vaporesso Luxe XR Max pod vape kit from £32.99 in 14 colours, and it takes the whole GTX coil range, so you can switch between MTL and DTL on the same device.

Vaporesso SWAG PX80 Not Firing or Showing an Error

The Vaporesso SWAG PX80 is a pod mod rather than a pod kit, and most of its faults are battery-related rather than pod-related. Two facts explain nearly all of them.

First, it takes a single external 18650 battery that is not included. A PX80 that will not turn on usually has no battery in it, a flat cell, or a cell inserted the wrong way round. Check that before anything else.

Second, it runs GTX coils in a pod tank, and the coil is locked in by rotating the drip tip rather than pushed in. A coil that is not locked will not read.

Screen shows a coil or atomizer error: unlock and reseat the GTX coil, then wipe the pod contacts and the mod's contacts dry.
Fires but tastes burnt: the 0.2 ohm GTX coil wants 45W to 60W and the 0.3 ohm wants 32W to 45W, so check the wattage matches the coil you fitted.
Weak or no draw: the airflow is adjusted by rotating the pod, so it may simply be closed.
Leaking from the base: the pod fills through a silicone plug underneath, so make sure it is pressed fully home.

Because it uses an external cell, treat a swollen, dented or wrapper-damaged 18650 as scrap and replace it rather than charging it. Availability on the Vaporesso SWAG PX80 moves, so check the product page before you plan around it.

Vaporesso Dojo Blast 10K Pod Problems and When to Swap the Pod

The Vaporesso Dojo Blast 10K is prefilled, so some XROS fixes simply do not apply. You cannot prime it, you cannot choose the liquid, and you cannot change the power.

What still applies:

Contact cleaning, exactly as above. A prefilled pod reads through contacts like any other.
Reseating the pod, then swapping it, in that order.
Checking for a cracked pod or one sitting at an angle.

What is different:

A burnt taste is not a priming problem, because the pod arrives filled. It is chain vaping, or a pod at the end of its life.
There is nothing to refill, so a worn pod gets replaced. Dojo Blast 10K pods are £4.99 and come prefilled with 20mg nic salt.
The 10,000 puff figure on the box is a brand claim, not a measurement, so treat it as a guide and judge by flavour instead.

If you are weighing prefilled against refillable, our comparison of vape pods and disposable style pods sets out the running costs either way.

How to Check Your Vaporesso Pods Are Genuine and UK Legal

A pod that will not read, or tastes wrong straight out of the packet, is sometimes the wrong pod rather than a faulty one.

Compatibility. The 0.4 ohm XROS pod is listed only for the XROS 4, XROS 4 Mini and XROS Pro, so it will not suit an XROS 3 or older device. Luxe XR and SWAG pods take GTX coils instead and are not interchangeable with XROS pods.
TPD compliance. A UK-legal pod holds no more than 2ml, any liquid in it is 20mg/ml nicotine or lower, and the product should be MHRA-notified.
Duty stamp. Vaping liquid made in or imported into the UK since 1 October 2026 must carry a vaping duty stamp on the retail packaging. Older unstamped stock can still be sold during a grace period ending 31 March 2027, after which every vaping product sold in the UK needs a valid stamp.
Capacity. Vaporesso sells larger pods for markets without a tank size limit, so a 4ml or 5ml pod is not what a UK kit ships with.

If a pod fails the first two checks, stop using it. The same authenticity checks apply across brands, and we cover how to spot the difference in our guide to TPD compliance and vape authenticity.

Which Vaporesso Kit to Pick if Yours Cannot Be Fixed

If the same fault follows the device through three different pods, and clean dry contacts plus a full charge have not fixed it, the device is the problem. Replace rather than repair, because Vaporesso's manual states only Vaporesso should repair the device and at this price a replacement usually costs less than the postage on a return.

Prices below are current at the time of writing, so check the product page before you buy.

Kit	Style	Price	Pod and coil	Pick it if
Vaporesso Dojo Blast 10K	Prefilled MTL, 1000mAh, inhale activated	£7.49	2ml prefilled pod plus refill container, 20mg nic salt	You want disposable-style simplicity with no filling or priming
Vaporesso XROS Mini	Refillable MTL, 1000mAh, 11W to 16W	£17.99	2ml refillable XROS Series pod, sealed coil	You want to choose your own liquid at the lowest running cost
Vaporesso Luxe XR Max	Refillable, 2800mAh, 5W to 80W, screen	From £32.99	2ml Luxe XR pod with separate GTX coils	You want MTL and DTL on one device, with wattage control
Vaporesso SWAG PX80	Pod mod, 5W to 80W, external 18650	£35.99	Pod tank with GTX coils	You already own 18650 cells and want a mod-style setup

For most people replacing a faulty pod kit, the Vaporesso XROS Mini pod vape kit at £17.99 is the like-for-like swap, because your existing XROS pods carry straight over. If the filling and priming is what put you off, the Dojo Blast 10K at £7.49 is the simpler route. If you want wattage control so you can stop burning coils, the Luxe XR Max is the step up.

Vaporesso Fixes: What to Do First

Almost every Vaporesso fault comes back to dirty or wet contacts, a wick fired dry, or a pod or coil that was not seated properly. The fix that solves the most faults for the least money is a fresh genuine pod or GTX coil kept spare in a drawer, because scorched cotton cannot be rescued. Replacing the device is the alternative, but only once the same fault has followed it through three pods. One thing to hold in mind: on the XROS Mini and Dojo Blast you cannot turn the power down, so liquid choice and puff spacing are your only levers, while on the Luxe XR Max and SWAG PX80 the wattage setting is usually the culprit.

Frequently Asked Questions

Why does my Vaporesso say no pod when there is a pod in it?

The device cannot read the coil through the contacts. Remove the pod, wipe the pod base and the pins inside the device with a dry cotton bud, and check the protective sticker is off if the kit is new. Refit it firmly, then try a different pod.

Can you fix a burnt XROS pod?

No. Once the cotton inside the pod is scorched, the taste is permanent and rinsing will not clear it. Replace the pod. Letting a pod soak only helps if you caught a dry hit before the cotton actually burned.

Do XROS pods fit the Luxe XR Max or SWAG PX80?

No. XROS pods have a sealed coil and only fit XROS devices. The Luxe XR Max and SWAG PX80 use their own pods with separate GTX coils, which are cross-compatible with each other but not with XROS.

Why is my XROS leaking after I fill it?

Usually the mouthpiece is not pushed fully home, or the pod was filled past the top of the window. Shut it firmly, fill lower next time, and dry the pod base before refitting. A pod that still weeps after that needs replacing.

Why will my Vaporesso SWAG PX80 not turn on?

It takes a single 18650 battery that is not supplied with the kit. Check a charged cell is fitted the right way round before anything else. If it still will not fire, reseat the GTX coil and wipe the contacts dry.